Goodbye
Old Standards Hello New!
EN 14351, the harmonised European Standard for windows
and doors is fast approaching - are you prepared?
Having for many years provided it's interpretations on CE Marking and
European Standards by placement of articles in the trade press, CENSolutions
Ltd., the UK technical consultancy and testing provider to the fenestration
industry, has been pleased to see that recently there has been a little
more publicity regarding the above mentioned EN 14351 standard. Some have
provided good advice while others have provided conflicting or contradictory
information. Wayne Rogerson, Joint Managing Director of CENSolutions Ltd.
has, however, been impressed by the refreshing approach being taken by
one aluminium system supplier. To ensure that all it's fabricators will
have a smooth transition to comply with EN 14351 by the deadline date
of the 1st February 2009 this foresighted supplier has put it's interpretations
and implications of the standard into writing for the benefit of its customer
base.
Wayne Rogerson remains concerned, however, by comments elsewhere such
as 'manufacturers do not have to CE Mark' and also that people still seem
to be more concerned about British Standards. The bottom line is that
any conflicting national standards have to be withdrawn. So why are we
wasting time, energy and resources on revisions to standards like BS 7412,
BS 644, BS 4873, BS 6375?
A good example is BS 6375-1___(Classification for weathertightness and
guidance on selection and specification). Although this standard was revised
and reissued in 2004, it still makes reference to the EN's, for example:-
* EN 12207 is the classification for air permeability.
* EN 12208 is the watertightness classification.
* EN 12210 is the resistance to wind load classification.
BS 6375 also states that they need to be tested in accordance with EN
1026, EN 1027 and EN 12211. With these European Norms being as good as
if not better than BS 6375, why is BS 6375 still around? It also begs
the question 'why waste the time and money in carrying out this irrelevant
revision?
The fact is that by still promoting and pushing the BS's, the Industry
Bodies are deflecting people's attention away from the more important
issue of the European Standards and the Construction Products Directive
(89/106/EEC). The Directive has been around for some years and whilst
it should be well known that CE Marking is not compulsory in the UK, what
appears to be not quite so well known is that it is mandatory to comply
with the Directive and it's associated standards. The majority of window
and door fabricators do not want to go down a third party accredited route
due to the unnecessary expense involved and as such will only require
to be compliant to EN 14351. This is why it is so important that EN 14351
gets sufficient publicity and exposure to properly inform the thousands
of manufacturers in the UK who need to be aware of what's happening.The
Construction Products Directive has already affected a large number of
manufacturers of products used in the fenestration industry including
EN 12150 (Toughened Safety Glass - mandatory on 1st September 2006) and
EN 1279 (Insulating Glass Units - mandatory on 1st March 2007). Now it's
the turn of window and door manufacturers to come under the spotlight.
So what is EN 14351? It is a new Harmonised European Standard for windows
and doors regardless of material (UPV-c, Aluminium, Timber or Steel).
All manufacturers of windows and doors will have to comply with the standard
by 1st February 2009. Failure to do so will mean that the company is trading
illegally. Where manufacturers of windows and doors are found to be non-compliant,
it is understood that Trading Standards Officers will have powers to apply,
if necessary, for custodial sentences of up to 3 months and/or a fine
of up to £5000. Indeed they may also force the manufacturer to cease
trading.
So what do the manufacturers of windows and doors need to do to remain
within the law? There are 4 mandatory requirements:
* Implementation of a system of Factory Production Control (FPC)
* Determination of Dangerous substances (Information from the system supplier)
* Determination of the Load bearing capacity of safety devices (Information
from the supplier of those particular hardware items, tested to EN 14609,
EN 958)
* Determination of Thermal transmittance (Calculations using EN 10077,
or hot box testing to EN 12567)
CENSolutions is well aware that other Member States in Europe are up to
speed on EN 14351 and that since some leading Pan European system suppliers
are ahead of the game, their fabricators will be provided with the necessary
information in anticipation of 1st February 2009. The question is, how
are we, the UK fenestration industry going to respond to this challenge?
It is sincerely hoped that we can respond quickly and that we do not find
ourselves lagging behind the other key European member states.
CENSolutions Ltd. has the necessary resources in place, coupled with relevant
experience to assist as many companies as possible through this legislation.
It is imperative that EN 14351 is high up on the New Year agenda for all
window and door fabricators.
Web: http://www.censolutions.com
